FAQ

 

Roof Information

  • SlimFit: SlimFit is designed to be installed on metal standing seams roofs that are at least 14.5” wide measured on center between the seams, and that are flat with no ribs or striations in the channels. Roof pitch must be less than 40 degrees. No roof penetrations or ballasts are needed.or ballasts are needed.

    FLEX: Flat (2 degree pitch or less) membrane roofs (TPO or EPDM). Low crickets are no problem. Installation of Flex modules on greater curves or slopes may be possible if the roof stack includes a gypsum board directly under the membrane. No roof penetrations or ballasts needed.

  • SlimFit: Yes- SlimFit can only be installed on slopes of less than 40 degrees.

    FLEX: FLEX modules are intended for installation on a flat membrane roof (2 degree pitch or less), but can be installed at higher slopes if a non-combustible backer-board (gypsum) is installed directly under the membrane.

  • Not at this time, but we can refer you to trusted metal roofing suppliers and installers.

  • Utility companies have different rules for how much you are allowed to oversize your solar system. Some will only allow a system size equal to your last 12 months of consumption history. Check with your local utility or solar installer for details. An additional concern would be the limits of your existing electric service panel for an over-sized solar system. Your installer will be able to evaluate your home’s electrical capabilities.

  • This is currently not possible as the adhesive used is not meant for vertical applications.

  • Although the module curves up to 30%, for designs with more than one module connected in a standing seam channel, the junction box covers may be a challenge. Every roof is unique and should be looked at on a case by case basis.

  • The SlimFit product is currently only available for residential and commercial use. Please visit Sunflare’s division for the mobile environment: XPLOR

Product Specifications

  • Flex: 0.5 lbs. per sq. ft.

    SlimFit: 0.5 lbs. per sq. ft

  • SlimFit: (connections on top corners only)

    1813 mm (71.37”) long X 358 mm (14.09”) wide (+-0.1 in.) X 2 mm thick

    SlimFit XT: (connections on top and bottom corners)

    1973 mm (77.67”) long X 358 mm (14.09”) wide (+-0.1 in.) X 2 mm thick

    FLEX: 65.4 inches X 38.9 inches (+-0.1 in.) 2 mm thick

  • They are a dark charcoal color. Below are pictures of a SlimFit module.

    Pantone Swatch

    SlimFit module

  • No.

  • All Array modules are tested from -40 degrees F up to 185 degrees F.

  • No.

  • No.

  • An Array system must be installed by a licensed solar installer or electrican. The Array 25 year warranty is only valid for installations performed by licensed professionals.

  • The SlimFit product is currently only available for residential and commercial use.

  • PowerFit20

    FLEX60

 

Technical Information

  • Please click HERE to access Sunflare’s component compatibility document.

    Battery compatibility sheet is coming soon.

  • SlimFit: 10.8 W/sq. ft.

    FLEX: 10.3 W/sq. ft.

  • PowerFit: 60 watts

    FLEX: 195 watts

  • Every utility territory has different rules for self-generators (homes and businesses with solar). Net Energy Metering (NEM) export compensation for excess energy produced and exported to the grid is typically reflected as monthly credits against the times you used electricity but the sun wasn’t shining (your modules were not producing). Check with your local utility for the details.

  • The Federal Investment Tax Credit is currently available for solar installations and can be carried forward for 10 years. Sunflare Solar cannot provide tax advice. Please consult with your CPA or tax advisor.

  • SlimFit: 65 watts

    SlimFit XT 65 watts

    FLEX: 185, 190, 195, 200 watts

Availability

  • We are currently accepting Purchase Orders for FLEX and SlimFit.

    Our first shipment of SlimFit will be in the spring of 2024, and will be based on accepted Purchase Orders. FLEX modules are available now.

    Due to overwhelming interest in SlimFit, we have formed a SlimFit waitlist.

    Access waitlist HERE.

    Anyone on the waitlist who submits a $500 deposit (refundable anytime) will receive a personalized Helioscope Report for their home or business, which will show the power production of the installed SlimFit array, and give the solar installer a big head start. All Purchase Orders are honored on a first-come-first-served basis.

  • Please contact your local installer to obtain a turnkey proposal cost with Array modules plus the additional electrical components, labor, permitting etc. Solar modules are just one piece of the system- so it’s best to speak to an installer who can discuss all aspects of the equipment and installation.

  • Sunflare sells our products directly to solar installers.

  • SlimFit- Coming Soon!

    FLEX60